Backgroundimage

Industry - EMC

Phoenix Testlab has one of the most experienced and competent laboratories in the world for EMC testing.

Since the introduction of the EMC Directive, we've been supporting national and international customers with a specialist team and we prepare ourselves for the ongoing development of technology with state-of-the-art equipment. Whether outdoor measurement sites, noise immunity tests or noise emission tests – we can offer you the best service.

Accreditation/certification

Accreditations: DIN EN ISO/IEC 17025:2018
Certifications: DIN EN ISO 9001:2015 and DIN EN ISO 14001:2015

Typical Standards for the applications listed above
  • EN 61000-6-1 (noise immunity for residential environments)
  • EN 61000-6-2 (noise immunity for industrial environments)
  • EN 61000-6-3 (noise emission for residential environments)
  • EN 61000-6-4 (noise emission for industrial environments)
  • IEC TS 61000-6-5 (noise emission for power stations)
  • EN 61131-2 (programmable logic controllers)
  • EN 61204-3 (power supply equipment)
  • EN 61326 (equipment for control and laboratory use)
  • EN 61547 (lighting equipment)
  • EN 61800-3 (adjustable speed electrical devices)
  • EN 55014 (household appliances, electric tools, and similar apparatus)
  • EN 55015 (lighting equipment)
  • EN 55022 and DIN EN 55011 (radiated and conducted noise emission)
  • EN 50091-2 (uninterruptible power supply, UPS)
EMC test laboratory equipment
  • Five anechoic chambers
    • Measuring paths of 3 m/5 m
    • Emission measurement up to 110 GHz
    • Field generation up to 40 V/m (up to 6 GHz)
  • Outdoor measurement site with up to 10 m measuring path
  • Conducted noise emission and noise immunity in the shielded chamber
  • Noise emission of the network harmonics for single and three-phase devices up to 32 A
  • Noise immunity to network harmonics for single and three-phase devices up to 32 A
  • System for the simulation of foreign networks (e.g., 115 V, 60 Hz) with up to 32 A per phase
  • Ring wave tests up to 7.8 kV
  • Test of slowly attenuated oscillating waves up to 2.5 kV
  • Surge tests up to 7.4 kV
  • Burst tests up to 4.8 kV
  • ESD tests up to 30 kV
Monitoring media equipment
  • Reproducible constructions on pre-assembled mounting systems
  • Standardized measuring procedure for recording analog and digital measured values
  • Various bus monitoring systems such as INTERBUS, CAN, DeviceNet™, Ethernet, PROFINET, and PROFIBUS
  • Optical speed detection system
  • System for measuring illuminance
  • Optical probes
  • Pneumatic finger for pneumatic actuation of buttons
PROFINET conformance test

Users of devices in industrial automation require permanent functional safety for the components used. The networking of products from different manufacturers places particular requirements on the interface.

Finde more information about Profinet conformance tests.

On-site testing/in-situ test

Tests are performed on plants and systems, which are too large or too heavy to be tested in the laboratory.

For these tests, the EMC team has mobile EMC measuring equipment, which can record or simulate all the relevant EMC phenomena of plants and systems at the installation location.

Mobile EMC measuring equipment includes:

  • Noise test receiver according to CISPR
  • Burst and surge generator
  • Mains simulation up to 200 A per phase

Trained on-site team for support solving EMC problems.

Extract from the relevant standards:

  • DIN EN 55011 radiated and conducted noise emission “on-site”
  • DIN EN 61000-4-4 burst tests
  • DIN EN 61000-4-2 ESD tests
  • DIN EN 61000-4-6 generator for conducted HF